12/10G-GH (GH High-head Gravel Pump) Parts Listtotal 29 items, 28 part codes, including ImpellerA05 (GGH10137) , Throat BushA05 (GGH10013) , Frame Plate LinerA05 (GGH10041) , Frame Plate Liner (SGGH10041) , Pump CasingA05 (GGH10131) , Pump CoverQT (GGH10292) etc.; look up the material, unit weight and all fitting models of a part.
It belongs to G(GH) Gravel & TBM Pumps. The table below lists all its parts from the factory parts book; the first items usually replaced are ImpellerA05 (GGH10137) , Throat BushA05 (GGH10013) , Frame Plate LinerA05 (GGH10041) , Frame Plate Liner (SGGH10041) .
Within a series, larger suction/discharge sizes generally mean higher flow, head and max particle size. The table lists models of this series with collected clean-water performance (parts-only models and frame variants are in the “Same-series Models” tags at the page bottom), so you can move up or down the range; click “Details” for the full parts list.
| models | Flow m³/h | Head m | Speed r/min | Rated Power kW | Particle Size mm | Action |
|---|---|---|---|---|---|---|
| 10/8S-GH | 216-936 | 8-52 | 500-1000 | 560 | 120 mm | Details |
| 10/8FF-GH | 216-936 | 8-52 | 500-1000 | 560 | 120 mm | Details |
| 12/10G-GH | 288-2808 | 16-80 | 350-700 | 1200 | 150 mm | This page |
The table below lists all parts of this model — part name, part code, material/spec, unit weight and unit. Click a part code to see its materials and every model it fits.
| Part Name | Part Code | Material / Spec | Unit Wt. | Unit |
|---|---|---|---|---|
| Locating Sleeve | G117 | CS1 | 9 | pc |
| Pump CasingA05 | GGH10131 | KmTBCr26 | 2100 | pc |
| Pump CoverQT | GGH10292 | QT500-7 | 222 | pc |
| ImpellerA05 | GGH10137 | KmTBCr26 | 624 | pc |
| Throat BushA05 | GGH10013 | KmTBCr26 | 344 | pc |
| Frame Plate LinerA05 | GGH10041 | KmTBCr26 | 315 | pc |
| Clamp Band | GGH10135 | 25 | 29.4 | pc |
| Joint PlateQT | GGH10032 | QT500-7 | 580 | pc |
| Split Suction Flange | GGH10130 | 20 | 149 | pc |
| Split Discharge Flange | GGH10221 | 20 | 180.2 | pc |
| Suction Gasket | FG10132 | Natural Rubber | — | pc |
| Stuffing Box | G078 | HT200 | 121.5 | pc |
| Lantern Ring | G063 | ATNi14Cu6 | 4.97 | pc |
| Packing Washer | G067 | 1Cr18Ni9Ti | 3.6 | pc |
| Split Gland | G044 | HT200 | 12.5 | pc |
| O-ring | G122 | NBR | — | pc |
| O-ring | G109 | NBR | — | pc |
| Bearing Body | G004M | QT500-7 | 295 | pc |
| End Cover | G024-10 | HT200 | 28 | pc |
| Grease Guard Ring | G046 | HT200 | 22.5 | pc |
| Labyrinth Sleeve (pump end) | G062-10 | HT200 | 21 | pc |
| Labyrinth Sleeve (drive end) | GAM062-10 | HT200 | 15 | pc |
| Shaft | G073M | 45 | 453.56 | pc |
| BSW Round NutG061 | SBB046-82 | 45 | 7.82 | pc |
| Gland BoltM20X85 | SBB047-82 | 45 | 0.51 | pc |
| Bearing Assembly | — | — | — | pc |
| Frame Plate Liner | SGGH10041 | A05 | — | pc |
| Shaft Sleeve | G075 | C21 / C23 / J04 / J05 | — | pc |
| Bearing Assembly | G005M | — | — | pc |
Weights are for reference onlyUnit weight varies with material, batch and minor structural changes, For reference only — actual weight per drawing and factory weighing. For exact weights call 13930163303 (WeChat same number) to verify.
Part codes of this model grouped by part name; click any code to see the models it fits.
| Pump Model | 12/10G-GH |
|---|---|
| Category | Slurry Pumps |
| Series | GH High-head Gravel Pump |
| Rated Power | 1200 kW |
| Flow | 288-2808 m³/h (80-780 L/s) |
| Head | 16-80 m |
| Speed | 350-700 r/min |
| Peak Efficiency | 73 % |
| NPSH | 2.0-10.0 m |
| Blades | — |
| Impeller Dia. | 950 mm |
| Max. Particle Size | 150 mm |
| Wet-end Material | High-chrome A05 (A07/A33/A49 optional) |
| Drive | CRZ, CV, DCZ, ZVZ |
| Shaft Seal | Gland packing, expeller seal, mechanical seal |
| Model Nomenclature | 6/4D-G: 6 insuction, 4 indischarge, D frame, G Gravel Pump. |
This model (Common to AH / HH / M / L / G Series) has a complete manual: structural drawings, assembly procedures, installation and alignment, operation and maintenance, parameter tables and troubleshooting.
Send “pump model + part code + material + quantity” for a fast quote. Even a single old part or a nameplate photo is enough — we will identify the part number from the parts book. Common wear parts (impeller, liner, throat bush, frame plate liner, shaft sleeve, stuffing box, expeller cover, expeller) are kept in stock.