6/4E-SH (SH Slurry Pump) Parts Listtotal 30 items, 29 part codes, including ImpellerQT D=589(Standard) (ESH4145) , Pump CasingQT (ESH4092M) , Pump CoverQT (ESH4013) , Split Gland (E044) , Gland BoltM16X55 (SBB047-82) , Shaft Sleeve (E075) etc.; look up the material, unit weight and all fitting models of a part.
It belongs to H / SH Series Slurry Pumps. The table below lists all its parts from the factory parts book; the first items usually replaced are ImpellerQT D=589(Standard) (ESH4145) , Pump CasingQT (ESH4092M) , Pump CoverQT (ESH4013) , Split Gland (E044) .
By the numbering rule “suction size / discharge size + frame letter + series” it reads: suction 6 in, discharge 4 in, E frame, SH series. The frame letter indicates the bearing frame size — the later the letter (C→D→E→F→S/T), the higher the power capacity; double letters (CC, DD, EE, FF) are reinforced frames of the same tier.This model and its part codes are compiled from the official part-code cross-reference; clean-water performance parameters are not yet collected.For flow / head / speed / motor data please contact us directly.
The table below lists all parts of this model — part name, part code, material/spec, unit weight and unit. Click a part code to see its materials and every model it fits.
| Part Name | Part Code | Material / Spec | Unit Wt. | Unit |
|---|---|---|---|---|
| O-ring | F064 | NBR | — | pc |
| O-ring | E109 | NBR | 1.88 | pc |
| Labyrinth Ring | E108 | HT200 | — | pc |
| Shaft Sleeve | E075 | 3Cr13 | 10.44 | pc |
| Locating Sleeve | EAM117 | 4Cr13 | 6.02 | pc |
| frame | E003M | HT200 | 154 | pc |
| Lantern Ring | E063 | 1Cr18Ni9Ti | 2.87 | pc |
| Packing Washer | E067 | 1Cr18Ni9Ti | 0.96 | pc |
| Split Gland | E044 | HT200 | 3.8 | pc |
| Pump CasingQT | ESH4092M | QT500-7 | 275 | pc |
| Pump CasingQT(mech-seal type) | ESH4092M-JM | QT500-7 | 275 | pc |
| Pump CoverQT | ESH4013 | QT500-7 | 155 | pc |
| Pump Cover(labyrinth-ring design)QT | ESH4013X | QT500-7 | 152 | pc |
| ImpellerQT D=589(Standard) | ESH4145 | QT500-7 | 99 | pc |
| Impeller Labyrinth Ring | D4151 | 1Cr18Ni9Ti | 4 | pc |
| Cover Labyrinth Ring | D4151 | 1Cr18Ni9Ti | 3 | pc |
| Pipe Joint | FSH6273 | 1Cr18Ni9Ti | 0.92 | pc |
| Bearing Body | E004M | HT200 | 58 | pc |
| End Cover | E024 | HT200 | 7 | pc |
| Grease Guard Ring | E046 | HT200 | 3.6 | pc |
| Labyrinth Sleeve | E062 | HT200 | 3.9 | pc |
| Shaft | EAM073M | 45 | 70.19 | pc |
| StudM24X64 | SBB033-82-17 | 45 | 0.44 | pc |
| BSW Round NutE061 | SBB046-82 | 45 | 1.41 | pc |
| Gland BoltM16X55 | SBB047-82 | 45 | 0.27 | pc |
| Lock WasherE011 | SBB048-82 | 45 | 0.74 | pc |
| Adjusting BoltM24X240 | SBB049-82 | 45 | 1.51 | pc |
| Casing BoltM24X260 | SBB052-82 | 45 | 1.93 | pc |
| KeyB22X185 | SBB063-82 | 45 | 0.89 | pc |
| Bearing Assembly | EAM005M | — | — | pc |
Weights are for reference onlyUnit weight varies with material, batch and minor structural changes, For reference only — actual weight per drawing and factory weighing. For exact weights call 13930163303 (WeChat same number) to verify.
Part codes of this model grouped by part name; click any code to see the models it fits.
Send “pump model + part code + material + quantity” for a fast quote. Even a single old part or a nameplate photo is enough — we will identify the part number from the parts book. Common wear parts (impeller, liner, throat bush, frame plate liner, shaft sleeve, stuffing box, expeller cover, expeller) are kept in stock.