8/6S-H (H Series Slurry Pumps) Parts Listtotal 52 items, 52 part codes, including ImpellerA05 (FH6147) , Expeller (8/6S-H-04) , LinerA05 (FH6110) , Throat BushA05 (8/6S-H-02a) , Frame Plate LinerA05 (FH4041) , Frame Plate Liner (FH6041) etc.; look up the material, unit weight and all fitting models of a part.
It belongs to H / SH Series Slurry Pumps. The table below lists all its parts from the factory parts book; the first items usually replaced are ImpellerA05 (FH6147) , Expeller (8/6S-H-04) , LinerA05 (FH6110) , Throat BushA05 (8/6S-H-02a) .
By the numbering rule “suction size / discharge size + frame letter + series” it reads: suction 8 in, discharge 6 in, S frame, H series. The frame letter indicates the bearing frame size — the later the letter (C→D→E→F→S/T), the higher the power capacity; double letters (CC, DD, EE, FF) are reinforced frames of the same tier.This model and its part codes are compiled from the official part-code cross-reference; clean-water performance parameters are not yet collected.For flow / head / speed / motor data please contact us directly.
The table below lists all parts of this model — part name, part code, material/spec, unit weight and unit. Click a part code to see its materials and every model it fits.
| Part Name | Part Code | Material / Spec | Unit Wt. | Unit |
|---|---|---|---|---|
| Suction Gasket | F6060 | Natural Rubber | — | pc |
| O-ring | F109 | NBR | — | pc |
| O-ring | FH122 | NBR | — | pc |
| ImpellerA05 | FH6147 | KmTBCr26 | 328 | pc |
| LinerA05 | FH6110 | KmTBCr26 | 335 | pc |
| Frame Plate LinerA05 | FH4041 | KmTBCr26 | 141 | pc |
| Shaft Sleeve | F075 | CS1 | 9 | pc |
| Locating Sleeve | FG117 | CS1 | 4 | pc |
| Guard Sleeve | S179-3 | CS1 | 6.3 | pc |
| Stuffing Box | FH078 | HT200 | 86 | pc |
| frameQT | S003M | QT500-7 | 546 | pc |
| Front Lantern Ring | F118-1 | 1Cr18Ni9Ti | 7.63 | pc |
| Liner Bolt | FH6256 | A3.A3F | 1.68 | pc |
| Split Gland | F044 | HT200 | 5.5 | pc |
| Impeller Removal Ring | S239M | CS1 | 8.2 | pc |
| Cover Stud | S30015M | 45 | 5.03 | pc |
| Spigot Washer | F080-1 | 20 | 0.37 | pc |
| Discharge Gasket | FHP6132 | Natural Rubber | — | pc |
| Liner Gasket | G8124 | Natural Rubber | — | pc |
| Labyrinth Ring | S108 | HT200 | 0.4 | pc |
| Pump Casing(8/6S-H frame only) | FH6032 | QT500-7 | 474 | pc |
| Pump Cover | 8/6S-H-03 | QT500-7 | 467 | pc |
| Throat BushA05 | 8/6S-H-02a | KmTBCr26 | 196 | pc |
| Seal Box | 8/6S-H-05 | ADI Ductile Iron | 86 | pc |
| Expeller | 8/6S-H-04 | ADI Ductile Iron | 39 | pc |
| frame | SX003A | QT500-7 | 546 | pc |
| Front Lantern Ring | 8/6S-H-06 | 1Cr18Ni9Ti | 6.11 | pc |
| Liner Seat Ring | FH6257 | Natural Rubber | — | pc |
| O-ring | CSC210 | NBR | — | pc |
| End-cover Gasket | S025 | Neoprene | — | pc |
| Bearing Body | S004M | QT500-7 | 151.5 | pc |
| Shaft | S073-3M | 45 | 238.53 | pc |
| End Cover | S024 | HT200 | 17.5 | pc |
| Labyrinth Sleeve (pump end) | S062 | QT500-7 | 9.6 | pc |
| Labyrinth Sleeve (drive end) | S062DM | QT500-7 | 14.5 | pc |
| ShaftSX073-3A | SX-01 | 45 | 284.04 | pc |
| Labyrinth SleeveSX062DA | SX-02 | HT200 | 8.7 | pc |
| End CoverSX024A | SX-03 | QT500-7 | 21.5 | pc |
| Oil/vent Plug | SX-04 | QT500-7 | 0.28 | pc |
| Bearing BodySX004A(QT) | SX-05 | 45 | 143 | pc |
| Labyrinth SleeveSX062A | SX-06 | QT500-7 | 8.8 | pc |
| Bottom Cover | SX-08 | HT200 | 1.56 | pc |
| Oil Slinger Ring | SX-11 | A3.A3F | 2.37 | pc |
| 3/8"Pipe Joint | B3201-03-1 | A3.A3F | 0.16 | pc |
| 3/8"PipeNut | B3201-03-2 | A3.A3F | 0.11 | pc |
| Gland BoltM20X75 | SBB047-82 | 45 | 0.47 | pc |
| Lock WasherF011 | SBB048-82 | 45 | 1.4 | pc |
| Adjusting BoltM30X345 | SBB049-82 | 45 | 3.44 | pc |
| Locating Wedge240X38 | SBB050-82 | A3.A3F | 0.67 | pc |
| Casing BoltM30X330 | SBB051-82 | 45 | 3.31 | pc |
| Bearing Assembly | S005-3M | — | — | pc |
| Frame Plate Liner | FH6041 | A05 / A49 / R55 / U01 | — | pc |
Weights are for reference onlyUnit weight varies with material, batch and minor structural changes, For reference only — actual weight per drawing and factory weighing. For exact weights call 13930163303 (WeChat same number) to verify.
Part codes of this model grouped by part name; click any code to see the models it fits.
This model (Common to AH / HH / M / L / G Series) has a complete manual: structural drawings, assembly procedures, installation and alignment, operation and maintenance, parameter tables and troubleshooting.
Send “pump model + part code + material + quantity” for a fast quote. Even a single old part or a nameplate photo is enough — we will identify the part number from the parts book. Common wear parts (impeller, liner, throat bush, frame plate liner, shaft sleeve, stuffing box, expeller cover, expeller) are kept in stock.