8/6X-HP (H Series Slurry Pumps) Parts Listtotal 41 items, 41 part codes, including ImpellerA05 (FH6147) , Expeller (8/6S-H-04) , LinerA05 (FH6110) , Throat BushA05 (8/6S-H-02a) , Frame Plate LinerA05 (FH4041) , Pump Casing(8/6S-HP frame only)QT (FHP6032) etc.; look up the material, unit weight and all fitting models of a part.
It belongs to H / SH Series Slurry Pumps. The table below lists all its parts from the factory parts book; the first items usually replaced are ImpellerA05 (FH6147) , Expeller (8/6S-H-04) , LinerA05 (FH6110) , Throat BushA05 (8/6S-H-02a) .
By the numbering rule “suction size / discharge size + frame letter + series” it reads: suction 8 in, discharge 6 in, X frame, HP series. The frame letter indicates the bearing frame size — the later the letter (C→D→E→F→S/T), the higher the power capacity; double letters (CC, DD, EE, FF) are reinforced frames of the same tier.This model and its part codes are compiled from the official part-code cross-reference; clean-water performance parameters are not yet collected.For flow / head / speed / motor data please contact us directly.
The table below lists all parts of this model — part name, part code, material/spec, unit weight and unit. Click a part code to see its materials and every model it fits.
| Part Name | Part Code | Material / Spec | Unit Wt. | Unit |
|---|---|---|---|---|
| Suction Gasket | F6060 | Natural Rubber | — | pc |
| O-ring | F109 | NBR | — | pc |
| O-ring | FH122 | NBR | — | pc |
| ImpellerA05 | FH6147 | KmTBCr26 | 328 | pc |
| LinerA05 | FH6110 | KmTBCr26 | 335 | pc |
| Frame Plate LinerA05 | FH4041 | KmTBCr26 | 141 | pc |
| Shaft Sleeve | F075 | CS1 | 9 | pc |
| Guard Sleeve | S179-3 | CS1 | 6.3 | pc |
| Liner Bolt | FH6256 | A3.A3F | 1.68 | pc |
| Split Gland | F044 | HT200 | 5.5 | pc |
| Impeller Removal Ring | S239M | CS1 | 8.2 | pc |
| Spigot Washer | F080-1 | 20 | 0.37 | pc |
| Discharge Gasket | FHP6132 | Natural Rubber | — | pc |
| Liner Gasket | G8124 | Natural Rubber | — | pc |
| Cover Stud | FP6015M | 45 | 6.98 | pc |
| Throat BushA05 | 8/6S-H-02a | KmTBCr26 | 196 | pc |
| Seal Box | 8/6S-H-05 | ADI Ductile Iron | 86 | pc |
| Expeller | 8/6S-H-04 | ADI Ductile Iron | 39 | pc |
| Front Lantern Ring | 8/6S-H-06 | 1Cr18Ni9Ti | 6.11 | pc |
| Liner Seat Ring | FH6257 | Natural Rubber | — | pc |
| Pump Casing(8/6S-HP frame only)QT | FHP6032 | QT500-7 | 735 | pc |
| Pump CoverQT | 8/6S-HP-01 | QT500-7 | 770 | pc |
| Shaft | 8/6X-HP-01 | 45 | 422.85 | pc |
| O-ring | CSC210 | NBR | — | pc |
| Dust Disc | SBB007-565-03 | HT200 | 9.7 | pc |
| Front Bearing Cover | SBB007-565-04 | HT150 | 17 | pc |
| Oil Slinger Disc | SBB007-565-05 | HT150 | 12.85 | pc |
| Oil Ring | SBB007-565-06 | A3.A3F | 9.13 | pc |
| Adjustment Cover | SBB007-565-08 | HT150 | 2.6 | pc |
| Long Sleeve | SBB007-565-12 | HT200 | 6.4 | pc |
| Water-cooled Gland | SBB007-565-13 | HT150 | 7 | pc |
| Removal Washer | SBB007-565-15 | A3.A3F | 7.28 | pc |
| Frame Body | SBB007-565A-01 | HT200 | 700 | pc |
| Frame Cover | SBB007-565A-02 | HT200 | 160 | pc |
| Bearing Sleeve | SBB007-565A-03 | HT200 | 45 | pc |
| Guard Sleeve | SBB007-565A-04 | HT150 | 3 | pc |
| Rear Bearing Cover | SBB007-565A-05 | HT150 | 15.6 | pc |
| Cooling-chamber CoverB | SBB007-760-06 | ZG230-450 | 14.5 | pc |
| Gland BoltM20X75 | SBB047-82 | 45 | 0.47 | pc |
| Locating Wedge240X38 | SBB050-82 | A3.A3F | 0.67 | pc |
| Casing BoltM30X330 | SBB051-82 | 45 | 3.31 | pc |
Weights are for reference onlyUnit weight varies with material, batch and minor structural changes, For reference only — actual weight per drawing and factory weighing. For exact weights call 13930163303 (WeChat same number) to verify.
Part codes of this model grouped by part name; click any code to see the models it fits.
This model (Common to AH / HH / M / L / G Series) has a complete manual: structural drawings, assembly procedures, installation and alignment, operation and maintenance, parameter tables and troubleshooting.
Send “pump model + part code + material + quantity” for a fast quote. Even a single old part or a nameplate photo is enough — we will identify the part number from the parts book. Common wear parts (impeller, liner, throat bush, frame plate liner, shaft sleeve, stuffing box, expeller cover, expeller) are kept in stock.