100ZG-Z (ZGB Slurry Pump) Parts Listtotal 43 items, 41 part codes, including Expeller (E028) , Liner Gasket (E4124) , Throat BushA05 (100ZG-Z-02) , Frame Plate LinerA05 (100ZG-Z-04) , Pump Casing (100ZG-Z-05) , Cover Stud (E4015M) etc.; look up the material, unit weight and all fitting models of a part.
It belongs to ZGB / ZG Series Slurry Pumps. The table below lists all its parts from the factory parts book; the first items usually replaced are Expeller (E028) , Liner Gasket (E4124) , Throat BushA05 (100ZG-Z-02) , Frame Plate LinerA05 (100ZG-Z-04) .
The table below lists all parts of this model — part name, part code, material/spec, unit weight and unit. Click a part code to see its materials and every model it fits.
| Part Name | Part Code | Material / Spec | Unit Wt. | Unit |
|---|---|---|---|---|
| Oil-cup Seat | D138 | 20 | 0.29 | pc |
| O-ring | E064 | NBR | — | pc |
| Locating Plate | E4081 | 20 | 0.33 | pc |
| Seal Gasket | E122 | Natural Rubber | — | pc |
| Cover Stud | E4015M | 45 | 3.19 | pc |
| Lock Sleeve | E117 | 4Cr13 | 4.21 | pc |
| Stuffing Box | E078 | HT200 | 19 | pc |
| Stuffing Box | E078JM | HT200 | 19 | pc |
| Expeller | E028 | HT200 | 8.2 | pc |
| Expeller Cover | E029 | HT200 | 17.6 | pc |
| O-ring | E109 | NBR | 1.88 | pc |
| Suction Gasket | E4060 | Natural Rubber | — | pc |
| Labyrinth Ring | E108 | HT200 | — | pc |
| Shaft Sleeve | E075 | 3Cr13 | 10.44 | pc |
| frame | E003M | HT200 | 154 | pc |
| Lantern Ring | E063 | 1Cr18Ni9Ti | 2.87 | pc |
| Front Lantern Ring | E118 | 1Cr18Ni9Ti | 4.08 | pc |
| Packing Washer | E067 | 1Cr18Ni9Ti | 0.96 | pc |
| Split Gland | E044 | HT200 | 3.8 | pc |
| Liner Gasket | E4124 | Natural Rubber | — | pc |
| Pump Casing | 100ZG-Z-05 | HT200 | 120 | pc |
| Pump CasingQT | 100ZG-Z-05 | QT500-7 | 120 | pc |
| Pump Cover | 100ZG-Z-06 | HT200 | 110 | pc |
| Pump CoverQT | 100ZG-Z-06 | QT500-7 | 110 | pc |
| ImpellerA05 | 100ZG-Z-01 | KmTBCr26 | 53 | pc |
| LinerA05 | 100ZG-Z-03 | KmTBCr26 | 88 | pc |
| Throat BushA05 | 100ZG-Z-02 | KmTBCr26 | 43 | pc |
| Frame Plate LinerA05 | 100ZG-Z-04 | KmTBCr26 | 48 | pc |
| Suction Pipe | 100ZG-Z-07 | ZG230-450 | 30 | pc |
| Discharge Pipe | 100ZG-Z-08 | ZG230-450 | 25 | pc |
| Locating Plate | 100ZG-Z-10 | 20 | 0.31 | pc |
| Bearing Body | E004A | HT200 | 58 | pc |
| Shaft | E073A | 45 | 72.28 | pc |
| End Cover | E024A | HT200 | 7 | pc |
| Grease Guard Ring | E046A | HT200 | 3.5 | pc |
| Labyrinth Sleeve | E062A | HT200 | 3.9 | pc |
| BSW Round NutE061 | SBB046-82 | 45 | 1.41 | pc |
| Gland BoltM16X55 | SBB047-82 | 45 | 0.27 | pc |
| Lock WasherE011 | SBB048-82 | 45 | 0.74 | pc |
| Adjusting BoltM24X240 | SBB049-82 | 45 | 1.51 | pc |
| Locating Wedge240X38 | SBB050-82 | A3.A3F | 0.67 | pc |
| Casing BoltM24X260 | SBB052-82 | 45 | 1.93 | pc |
| KeyB22X185 | SBB063-82 | 45 | 0.89 | pc |
Weights are for reference onlyUnit weight varies with material, batch and minor structural changes, For reference only — actual weight per drawing and factory weighing. For exact weights call 13930163303 (WeChat same number) to verify.
Part codes of this model grouped by part name; click any code to see the models it fits.
This model (ZGB / ZG Series Slurry Pumps) has a complete manual: structural drawings, assembly procedures, installation and alignment, operation and maintenance, parameter tables and troubleshooting.
Send “pump model + part code + material + quantity” for a fast quote. Even a single old part or a nameplate photo is enough — we will identify the part number from the parts book. Common wear parts (impeller, liner, throat bush, frame plate liner, shaft sleeve, stuffing box, expeller cover, expeller) are kept in stock.